Want to get the best results from your 3D printer? Check out our guide to the best 3D printer slicer software. Even better, most of them are free. How to setup Ideamaker 3D slicer for use with your CR-10. Apple software update free download. If you are switching from Cura or other slicer, this will help you get setup using your CR-10 or ot. It was developed by the 3D printer giant Ultimaker and used by the company’s community of.
ok i think i found whats happening : your nozzle is a little bit blocked and don't extrude the correct diameter for your settings. it dont affect plane straight lines or big circles, but when it turns very quick the material won't stick.
3 solutions :
a) in your slicer adjust line widht t the real width of your filament extruded .. to do so :
put your head high overs the bed, fan off, help extrude a little bit and wait for the filament to do a ligne of 10 cm / 4 inches approx. when cold use a gauge or a caliper to mesure it : it shoud be round an about 0,4 mm but yours i probably 0.3. if its round adjust the line width in your slicer
b) use the little tool (like a pin) sold with your printer and put it in the nozzle when its hot (be carreful : ITS DAMN HOT and it will heat the pin fast !!!!!!! i will be not responsible for any injuries) then extrude 10 cm of plastic and verify with the a) method.
c) change your nozzle (it must be HOT to do so ! and be carefull again !!!! i ll be still ot responsable of your burns.. Best 3d home design software mac. nor the less any way :) )
3 solutions :
a) in your slicer adjust line widht t the real width of your filament extruded .. to do so :
put your head high overs the bed, fan off, help extrude a little bit and wait for the filament to do a ligne of 10 cm / 4 inches approx. when cold use a gauge or a caliper to mesure it : it shoud be round an about 0,4 mm but yours i probably 0.3. if its round adjust the line width in your slicer
b) use the little tool (like a pin) sold with your printer and put it in the nozzle when its hot (be carreful : ITS DAMN HOT and it will heat the pin fast !!!!!!! i will be not responsible for any injuries) then extrude 10 cm of plastic and verify with the a) method.
c) change your nozzle (it must be HOT to do so ! and be carefull again !!!! i ll be still ot responsable of your burns.. Best 3d home design software mac. nor the less any way :) )
Creality Slicer
Acrobat reader for free. software download. any way i use a slightly reduced line width to improve my prints (0.35 for a 0.40 extruder)
My PC (Linux Mint) sits right next to my CR10 and I'd like to be able to send files directly to it rather than load the SD card in to the PC, save the file, unplug the SD card, plug it into the CR10 control box, etc etc. I have a USB cable plugged into the CR10 and into a USB hub from my PC but the PC doesn't see the printer. I don't know what to do in Cura to make it recognize the printer- it lists the printer as the default from when I set up Cura but says it's not connected. The CR10 'manual' doesn't say one word about the USB port on the CR10 control box.
Creality Cr 10 Slicer
![Creality cr 10 slicer software freeware Creality cr 10 slicer software freeware](https://cdn.shopify.com/s/files/1/0221/1404/products/s-l1600_7bc85b54-7af6-4efb-911b-4e1c7dfbe48b_x700.jpg?v=1542899332)